ATR stop loss for crypto: formula, multiples and fee check

An ATR stop loss sits a multiple of the Average True Range (ATR) away from the entry, so the stop distance follows how far the market normally moves: long stop = entry − k × ATR, short stop = entry + k × ATR, and the loss when it fills = stop distance + round-trip fees. Example: with an ATR of 600 on a 60,000 entry and k = 2, the long stop is 60,000 − 2 × 600 = 58,800, a 2% stop; with 0.12% round-trip fees (0.06% taker each way) the loss at the stop is 2.12% of the position, and fees are 6% of the stop distance.

How ATR is calculated

The true range (TR) of a candle is the largest of three distances: high − low, |high − previous close| and |low − previous close|. The last two catch gaps between candles. ATR is the average true range over the last n candles; 14 is a common default, and TradingView's built-in ATR uses Wilder's smoothing.

Example candle: high 60,500, low 59,900, previous close 60,700. The high-low range is 600, but the true range is 800, because the whole candle traded below the previous close and the gap counts.

ATR is measured in price, so the same ATR is a different percentage at a different price, and every timeframe has its own ATR. The ATR of 600 on this page is a fixed example value, not a live reading.

The formula

  • Long: stop = entry − k × ATR. Short: stop = entry + k × ATR.
  • In the example, k = 2 gives 58,800 for a long and 61,200 for a short.
  • Loss at the stop = stop distance + round-trip fees (+ slippage on a stop-market fill).

Multiples compared

The table holds the risk amount fixed and sizes each position so a stop-out loses that amount, fees included.

Multiples compared
ATR multiple (k)Long stopStop distanceLoss at stop with feesFees ÷ stop distanceSize for $100 risk
1 × ATR59,4001%1.12%12%$8,929
1.5 × ATR59,1001.5%1.62%8%$6,173
2 × ATR58,8002%2.12%6%$4,717
3 × ATR58,2003%3.12%4%$3,205

There is no universally right k. Traders commonly test values between about 1 and 3 on their own market and timeframe. A small k is reached by ordinary movement more often; a large k is reached less often but gives up more price each time. With position size set from the stop, a wider stop does not lose more money — the position gets smaller — and fees take a smaller share of each loss.

The fee check

Compare the round-trip fee with one ATR. Here the 0.12% round trip against an ATR of 1% of price is 12% of one ATR. When that share is large, the timeframe is expensive to trade: the stop and the target have to be several ATR wide before fees stop dominating. On 1-minute charts the round trip can be larger than one ATR — see how much fees cost a crypto scalper.

Then size the position

With $100 at risk and the 2% stop, the position is $100 ÷ (2% + 0.12%) = $4,717 notional. The method is in how to calculate position size with fees. Check that liquidation sits beyond the stop: at 10x it is less than 10% away.

Structure first, ATR second

An ATR stop sets a distance, not a reason. Most traders anchor the stop to the price that proves the trade wrong and use ATR to check that it is not inside normal noise — see where to put a stop loss.

A trailing ATR stop moves the stop to the highest price since entry − k × ATR for a long and never moves it back. It exits with a stop-market order, so it pays the taker fee and can slip.

On your chart: Cost Compass

Cost Compass is a TradingView indicator from loweef that shows how far your break-even after round-trip fees and funding sits from entry in percent and in ATR, plus an approximate liquidation price — the fee check and the liquidation check from this page on your own chart. It is part of the Compass series. It shows states and estimated costs; it does not tell you when to buy or sell. Access is free right now and granted on request: send a private message to loweef on TradingView with your TradingView username. You do not need a loweef account to get access.

Fees are part of the math

Every stop-out pays two fees, so lower fees shrink every row of the table. With a 70% fee rebate (the Toobit rate through loweef) the 0.12% round trip nets 0.036%. The exchange charges the full fee when the stop fills; the rebate arrives afterwards. Check how much your fees would return.

Limits

The example treats both fees as a share of the entry value and ignores slippage, which is often largest exactly when a stop fills in a fast move (slippage vs trading fee). Liquidation distances are upper bounds from leverage only. This page explains arithmetic. It is not financial advice and does not tell you when to buy or sell.

How much did you pay in futures fees this year? See your fee receipt →

Frequently asked questions

What is a good ATR multiple for a stop loss?

There is no single right value. Traders commonly test about 1 to 3 ATR on their own market and timeframe, and check that the stop also sits beyond the price that proves the trade wrong.

Which ATR length should I use?

14 candles is a common default and is what TradingView's built-in ATR starts with. A shorter length reacts faster to changes in volatility; a longer one is smoother.

Does a wider ATR stop mean a bigger loss?

Not if you size from the stop. The position gets smaller as the stop gets wider, so a stop-out loses the same planned amount. Fees take a smaller share of that loss.

How do I check whether fees are too high for my timeframe?

Divide the round-trip fee by one ATR in percent of price. If fees are a large share of one ATR, price has to move several ATR before a trade covers its costs.

Related terms

Trading fee Payback

Related questions

Last checked: 2026-10-28